Use Code MEGA3 for an Extra 3% Off
Free Shipping On Orders Over $1500
America's Leading Discount HVAC Supplier Since 2001
Ask an Expert
866 862 8922
Hours of Operation 8am - 8pm EST
8am - 8pm EST
- 2 ton - best for spaces between 1000 - 1200 sq ft depending on your home's insulation and your climate
- SEER2 rating helps consumers compare energy efficiency when choosing a new air conditioner. Higher SEER2 ratings mean significant utility savings. The federal minimum is 14 SEER2 with ratings into the 20 SEER2 range. A 20 SEER2 uses half the energy of a 10 seer much like MPG ratings for vehicles.
- If you have an indoor furnace, or air handler, along with an outdoor AC unit, this system will serve as a replacement for both.
- Best for cold climates and if you already have a gas furnace or a gas fuel supply already available.
- You'll need about 25-30 Btu's per sq. foot for warmer winter climates and about 35-50 Btu's per sq. foot for colder winter climates - highly dependent on construction type and insulation values.
Goodman 2 Ton 14 SEER2 80000 BTU 96% AFUE Two Stage Multi-Speed ECM Gas Furnace System - Horizontal | R32
- Condenser: GLXS3BN2410
- Gas Furnace: GR9T960803BN
- Evaporator Coil: CHPTA2426B3
Furnace BTU Sizing Tonnage Calculator
Heating Square Footage Range by Climate Zone
| Region 1 | Region 2 | Region 3 | Region 4 | Region 5 |
| 30 - 35 BTU's per square foot | 35 - 40 BTU's per square foot | 40 - 45 BTU's per square foot | 45 - 50 BTU's per square foot | 50 - 60 BTU's per square foot |
- 2 ton - best for spaces between 1000 - 1200 sq ft depending on your home's insulation and your climate
- SEER2 rating helps consumers compare energy efficiency when choosing a new air conditioner. Higher SEER2 ratings mean significant utility savings. The federal minimum is 14 SEER2 with ratings into the 20 SEER2 range. A 20 SEER2 uses half the energy of a 10 seer much like MPG ratings for vehicles.
- If you have an indoor furnace, or air handler, along with an outdoor AC unit, this system will serve as a replacement for both.
- Best for cold climates and if you already have a gas furnace or a gas fuel supply already available.
- You'll need about 25-30 Btu's per sq. foot for warmer winter climates and about 35-50 Btu's per sq. foot for colder winter climates - highly dependent on construction type and insulation values.
Goodman 2 Ton 13.4 SEER2 R32 Cooling Only Condenser
Model Number
GLXS3BN2410
Dimensions
26" W x 26" D x 27-1/2" H
Documents
Warranty
Parts: 10 years
Goodman R32 80000 BTU 96% Multi-Speed ECM Furnace Upflow / Horizontal
Model Number
GR9T960803BN
Dimensions
17-1/2" W x 28-3/4" W x 34-1/2" H
Documents
Limited Warranty
Heat Exchanger: Limited Lifetime | Parts: 10 years
Goodman 2 Ton R32 Evaporator Coil With Internal TXV Horizontal
Model Number
CHPTA2426B3
Dimensions
17-1/2" W x 21" D x 26" H
Documents
Warranty
Parts: 10 years
AHRI Number
215276963
GLXS3B Overview
Product Benefits:
- Energy-Efficienct Compressor
- Fully charged for 15' of tubing length
- Copper tube/ enhanced aluminum fin coil-5mm diameter
- Factory-installed filter drier
- Sweat connection service valves with easy access to gauge ports
- Enclosed contactor with lug connection
- High-pressure switch
- Capacitors with extended life
- AHRI Certified
- ETL Listed
Cabinet Features:
- Removable grille-style top design compliant with UL 60335-2-40
- Venturi for increased velocity of airflow
- Attractive Architectural Gray powder-paint finish with 500-hour salt-spray approval
- Wire fan discharge grille
- Steel louver coil guard
- Top and side maintenance access
- Single-panel access to controls with space provided for field-installed accessories
- When properly anchored, meets the 2023 Florida Building Code unit integrity requirements for hurricane-type winds (Anchor bracket kits available.)
GR9T96 Overview
Standard Features
- Energy-efficient, multi-speed ECM blower motor
- Heavy-duty, aluminized-steel tubular heat exchanger
- Stainless-steel secondary heat exchanger
- Two-stage gas valve provides quiet, economical heating
- Durable Silicon Nitride igniter
- Quiet two-speed induced draft blower
- Self-diagnostic control board with constant memory fault code history output to a LED
- Color-coded low-voltage terminals with provisions for electronic air cleaner and humidifier
- Low continuous fan speed options offer quiet air circulation
- All models comply with California 40 ng/J Low NOx emissions standard
- Can not be installed in California’s South Coast AirQuality Management District (SCAQMD) and San Joaquin Valley Air Pollution Control District (SJVAPCD).
- AHRI Certified; ETL Listed
Cabinet Features
- Designed for multi-position installation —
- GR9T96: upflow, horizontal left or right
- GD9T96: downflow, horizontal left or right
- Certified for direct vent (2-pipe) or non-direct vent (1-pipe)
- Easy-to-install top venting with optional side venting — GR9T96/upflow models only
- Convenient left or right connection for gas and electrical service
- Cabinet air leakage (QLeak) ≤ 2%
- Heavy-gauge steel cabinet with durable finish
- Fully insulated heat exchanger and blower section
- Airtight solid bottom or side return with easy-cut tabs for effortless removal in bottom air-inlet applications
CHPTA Overview
Standard Features
- All-Aluminum evaporator coil
- Optimized for use with R-32 refrigerant including circuits and manifolds
- R-32 sensor designed for the life span of the coil
- CAPTA and CHPTA models feature factoryinstalled thermal expansion valves for cooling and heat pump applications
- Standardized copper suction tube stub length
- Vertical and horizontal models available
- 21" depth for easier attic access
- CAPTA and CHPTA models include a single front access panel
- Foil-faced insulation covers the internal casing to reduce cabinet condensation
- Galvanized, leather grain-embossed finish
- Rust resistant, thermoplastic drain pans featuring a low water-retention design
- DecaBDE-free thermoplastic drain pan with secondary drain connections
- Drain pan rails designed to remove and reposition coils with ease without compromising structural integrity
- UV-resistant drain pan
- AHRI certified; ETL listed
Note: Do not use these coils on oil furnaces or any applications where the temperature on the drain pan may exceed 300° F. If these coils are applied with an oil furnace or another application where high temperatures threaten or jeopardize the durability of the drain pan, you must replace the factory-installed drain pan with a high-temperature drain pan. High-temperature drain pan kits are available as field-installed accessories.
Who installs the AC unit after I purchase it?
ACDirect does not yet provide installation services directly. However, most of our customers successfully arrange installation through local licensed HVAC contractors. These systems are designed for professional installation and typically include the components your installer will need.
Here’s how it works:
- Hire a licensed HVAC technician in your area
- Use platforms like Angi, Thumbtack, or a local HVAC directory to find reliable professionals
- Confirm your installer is experienced with the system type you’re purchasing
Note:
Please be aware if you choose to install HVAC equipment yourself and don’t possess proper HVAC licensing, you will void the manufacturer’s factory warranty. If you are capable of a factory-compliant installation yourself, you will need a licensed HVAC contractor to sign off on your work, fully confirming factory-compliant workmanship.
Need help? Contact Our Experts
(866)-862-8922
Hours:
Monday - Friday: 8am to 9pm EST
Saturday: 8am to 8pm EST
Sunday: 11am to 8pm EST