America's Leading Discount HVAC Supplier Since 2001 ...
and now, NASCAR Racing Sponsor
Ask an Expert
866 862 8922
Hours of Operation 8am - 8pm EST
11am - 8pm EST
- 2 ton - best for spaces between 1000 - 1200 sq ft depending on your home's insulation and your climate
- SEER2 rating helps consumers compare energy efficiency when choosing a new air conditioner. Higher SEER2 ratings mean significant utility savings. The federal minimum is 14 SEER2 with ratings into the 20 SEER2 range. A 20 SEER2 uses half the energy of a 10 seer much like MPG ratings for vehicles.
- If you have an indoor furnace, or air handler, along with an outdoor AC unit, this system will serve as a replacement for both.
- Best for cold climates and if you already have a gas furnace or a gas fuel supply already available.
- You'll need about 25-30 Btu's per sq. foot for warmer winter climates and about 35-50 Btu's per sq. foot for colder winter climates - highly dependent on construction type and insulation values.
- Best for mild to cold climates. The heat pump is the primary heat source and the gas furnace works for supplement heating when the temperature drops down to about 30 degrees or so
Goodman 2 Ton 17.2 SEER2 40000 BTU 96% Two Stage Variable Speed Gas Hybrid Heat Pump Dual System Upflow
- Condenser: GSZC702410
- Gas Furnace: GMVC960403BN
- Evaporator Coil: CAPTA3626B4
PRODUCT CLOSE-OUT ALL SALES FINAL. Click here for more details.
Furnace BTU Sizing Tonnage Calculator
Heating Square Footage Range by Climate Zone
| Region 1 | Region 2 | Region 3 | Region 4 | Region 5 |
| 30 - 35 BTU's per square foot | 35 - 40 BTU's per square foot | 40 - 45 BTU's per square foot | 45 - 50 BTU's per square foot | 50 - 60 BTU's per square foot |
- 2 ton - best for spaces between 1000 - 1200 sq ft depending on your home's insulation and your climate
- SEER2 rating helps consumers compare energy efficiency when choosing a new air conditioner. Higher SEER2 ratings mean significant utility savings. The federal minimum is 14 SEER2 with ratings into the 20 SEER2 range. A 20 SEER2 uses half the energy of a 10 seer much like MPG ratings for vehicles.
- If you have an indoor furnace, or air handler, along with an outdoor AC unit, this system will serve as a replacement for both.
- Best for cold climates and if you already have a gas furnace or a gas fuel supply already available.
- You'll need about 25-30 Btu's per sq. foot for warmer winter climates and about 35-50 Btu's per sq. foot for colder winter climates - highly dependent on construction type and insulation values.
- Best for mild to cold climates. The heat pump is the primary heat source and the gas furnace works for supplement heating when the temperature drops down to about 30 degrees or so
As low as $4,516.00
Free Shipping
Over $1500
*Excludes Commercial Products
DELIVERY TIME 3-10 BUSINESS DAYS
EXCLUDING WEEKENDS AND HOLIDAYS
ProfessionalU.S. Support
GUARANTEED LOWEST PRICES
FREE
SHIPPING
OVER $1500
*Excludes Commercial Products
DELIVERY TIME
3 - 10 BUSINESS DAYS
EXCLUDING WEEKENDS AND HOLIDAYS
PROFESSIONAL
U.S. SUPPORT
ADD TO CART FOR
GUARANTEED LOWEST PRICES
0% Interest
Orders $3000+ offered at checkout
No Credit Needed
Bad credit/no credit is OK - offered at checkout
Orders over $3000 get a
7 night luxury resort stay
Goodman 2 Ton 17.2 SEER2 Premium Series Two Stage Heat Pump Condenser
Model Number
GSZC702410
Dimensions
35-1/2" W x 35-1/2" D x 39-1/2" H
Documents
Warranty
Unit: 10 years | Compressor: Lifetime
Goodman 40000 BTU 96% Variable Speed Gas Furnace Upflow/Horizontal
Model Number
GMVC960403BN
Dimensions
17-1/2" W x 28-7/816" D x 34-1/2" H
Documents
Limited Warranty
Heat Exchanger: Limited Lifetime | Unit Replacement: 10 years | Parts: 10 years
Goodman 3 Ton Evaporator Coil With TXV Built In Upflow/Downflow 17-1/2"
Model Number
CAPTA3626B4
Dimensions
17-1/2" W x 21" D x 26" H
Documents
Limited Warranty
Parts: 10 years
AHRI Number
211641763
GSZC7 Condenser
Standard Features
- Two-Stage Copeland® UltraTech scroll compressor
- High-density foam compressor sound blanket
- Integrated communicating ComfortBridgeTM technology
- Commissioning and diagnostics via indoor board Blue-tooth with the CoolCloudTM phone and tablet application
- ComfortAlertTM built in diagnostics
- Copper tube/enhanced aluminum fin coil- 5mm on 2.0-3.0T
- Efficient, two-speed ECM condenser fan motor
- Simple low-voltage wiring to out-door unit in communicating mode
- Diagnostic indicator lights and storage of six fault codes
- Color-coded terminal strip for non-communicating set-up
- High- and low-pressure switches
- Time-delay technology with short-cycle protection to ensure quiet, reliable defrost
- Factory-installed bi-flow liquid-line filter drier
- Factory-installed suction-line accumulator
- Factory-installed compressor crankcase heater
- Factory-installed high-capacity muffler
- Factory-installed coil and ambient temperature sensors
- AHRI Certified; ETL Listed
Cabinet Features
- Grille-style sound control top design
- Custom Nickel Gray powder-paint finish
- 500-hour salt-spray tested
- Wire fan discharge grille
- Steel louver coil guard
- Single panel access to controls
- with space provided for field-installed accessories
- Sweat connection service valves with easy access to gauge ports
- When properly anchored, meets the 2020 Florida Building Code unit integrity requirements for hurricane-type winds (Anchor bracket kits available.)
GMVC96 Furnace
Standard Features
- Integrated communicating ComfortBridge™ Technology
- Commissioning and diagnostics via on board Bluetooth with the CoolCloud phone and tablet application
- Heavy-duty aluminized-steel tubular heat exchanger
- Stainless-steel secondary heat exchanger
- Two-stage gas valve provides quiet, economical heating
- Durable Silicon Nitride igniter
- Quiet two-speed induced draft blower
- Compatible with any single-stage thermostat
- Self-diagnostic control board with constant memory fault code history output to a triple 7-segment display
- Color-coded low-voltage terminals with provisions for electronic air cleaner
- Efficient and quiet variable-speed airflow system gently ramps up or down according to heating or cooling demand
- Multiple continuous fan speed options offer quiet air circulation
- Auto-Comfort and enhanced dehumidification modes available
- All models comply with California 40 ng/J Low NOx emissions standard
- Can no longer be installed in California’s South Coast Air Quality Management District (SCAQMD) on or after October 1, 2019.
Cabinet Features
- Designed for multi-position installation — upflow, horizontal left or right
- Certified for direct vent (2-pipe) or non-direct vent (1-pipe)
- Easy to install top venting with optional side venting
- Convenient left or right connection for gas and electrical service
- Cabinet air leakage (QLeak) <e; 2%
- Heavy-gauge steel cabinet with durable baked-enamel finish
- Fully insulated heat exchanger and blower section
- Airtight solid bottom or side-return with easy-cut tabs for effortless removal in bottom air-inlet applications
CAPTA Indoor Coil
Standard Features
- All-Aluminum evaporator coil
- Optimized for use with R-410A refrigerant
- Some models suitable for use with R-410A or R-22 refrigerant
- CAPT, CAPTA, CHPT, CHPTA models feature factory-installed thermal expansion valves for cooling and heat pump applications
- CAPF, CAPFA, CAUF, CAUFA, CHPF, CSCF models feature a check flowrator for cooling and heat pump applications
- Vertical and horizontal models available
- 21” depth for easier attic access
- Foil-faced insulation covers the internal casing to reduce cabinet condensation
- Galvanized,leather grain-embossed finish
- Rust resistant, thermoplastic drain pans featuring a low water-retention design
- DecaBDE-free thermoplastic drain pan with secondary drain connections
- UV-resistant drain pan
- AHRI Certified; ETL Listed
Product Documents
Who installs the AC unit after I purchase it?
ACDirect does not yet provide installation services directly. However, most of our customers successfully arrange installation through local licensed HVAC contractors. These systems are designed for professional installation and typically include the components your installer will need.
Here’s how it works:
- Hire a licensed HVAC technician in your area
- Use platforms like Angi, Thumbtack, or a local HVAC directory to find reliable professionals
- Confirm your installer is experienced with the system type you’re purchasing
Note:
Please be aware if you choose to install HVAC equipment yourself and don’t possess proper HVAC licensing, you will void the manufacturer’s factory warranty. If you are capable of a factory-compliant installation yourself, you will need a licensed HVAC contractor to sign off on your work, fully confirming factory-compliant workmanship.
Need help? Contact Our Experts
(866)-862-8922
Hours:
Monday - Friday: 8am to 9pm EST
Saturday: 8am to 8pm EST
Sunday: 11am to 8pm EST
