America's Leading Discount HVAC Supplier Since 2001 ...
and now, NASCAR Racing Sponsor
Ask an Expert
866 862 8922
Hours of Operation 8am - 8pm EST
11am - 8pm EST
- 4 ton - best for spaces between 2000-2400 sq ft depending on your home's insulation and your climate
- SEER2 rating helps consumers compare energy efficiency when choosing a new air conditioner. Higher SEER2 ratings mean significant utility savings. The federal minimum is 14 SEER2 with ratings into the 20 SEER2 range. A 20 SEER2 uses half the energy of a 10 seer much like MPG ratings for vehicles.
- If you have an indoor furnace, or air handler, along with an outdoor AC unit, this system will serve as a replacement for both.
- Best for cold climates and if you already have a gas furnace or a gas fuel supply already available.
- You'll need about 25-30 Btu's per sq. foot for warmer winter climates and about 35-50 Btu's per sq. foot for colder winter climates - highly dependent on construction type and insulation values.
Goodman 4 Ton 14 SEER2 100000 BTU 92% Single Stage Natural Gas System Horizontal
Furnace BTU Sizing Tonnage Calculator
Heating Square Footage Range by Climate Zone
| Region 1 | Region 2 | Region 3 | Region 4 | Region 5 |
| 30 - 35 BTU's per square foot | 35 - 40 BTU's per square foot | 40 - 45 BTU's per square foot | 45 - 50 BTU's per square foot | 50 - 60 BTU's per square foot |
- 4 ton - best for spaces between 2000-2400 sq ft depending on your home's insulation and your climate
- SEER2 rating helps consumers compare energy efficiency when choosing a new air conditioner. Higher SEER2 ratings mean significant utility savings. The federal minimum is 14 SEER2 with ratings into the 20 SEER2 range. A 20 SEER2 uses half the energy of a 10 seer much like MPG ratings for vehicles.
- If you have an indoor furnace, or air handler, along with an outdoor AC unit, this system will serve as a replacement for both.
- Best for cold climates and if you already have a gas furnace or a gas fuel supply already available.
- You'll need about 25-30 Btu's per sq. foot for warmer winter climates and about 35-50 Btu's per sq. foot for colder winter climates - highly dependent on construction type and insulation values.
As low as $5,573.00
Free Shipping
Over $1500
DELIVERY TIME 5-10 BUSINESS DAYS
EXCLUDING WEEKENDS AND HOLIDAYS
Professional Support Staff
GUARANTEED LOWEST PRICES
FREE
SHIPPING
OVER $1500
DELIVERY TIME
5 - 10 BUSINESS DAYS, EXCLUDING WEEKENDS AND HOLIDAYS
PROFESSIONAL
SUPPORT STAFF
ADD TO CART FOR
GUARANTEED LOWEST PRICES
0% Interest
Orders $3000+ offered at checkout
No Credit Needed
Bad credit/no credit is OK - offered at checkout
Orders over $2500 get a
7 night luxury resort stay
Goodman 4 Ton 14.3 SEER2 Straight Cool Condenser Value Line
Model Number
GSXN404810
Dimensions
35-1/2" W x 35-1/2" D x 39-1/2" H
Documents
Limited Warranty
10 years
Goodman GM9S 100000 BTU 92% Natural Gas Furnace Single Stage Upflow/Horizontal
Model Number
GM9S921005CN
Dimensions
21" W x 28-7/8" D x 34-1/2" H
Documents
Warranty
Heat Exchanger: Limited Lifetime | Parts: 10 years
Goodman 4-5 Ton Evaporator Coil with TXV Built in Horizontal 24"
Model Number
CHPT4860D4
Dimensions
26" W x 21 1/8" D x 24.5" H
Documents
Limited Warranty
10 years
AHRI
208800453
GSXN4 Condenser
Standard Features
- Energy-Efficient Compressor
- Copper tube/ enhanced aluminum fin coil-5mm diameter on 1.5-4.0T
- Factory-installed filter drier
- Fully charged for 15’ of tubing length
- Service valves with sweat connections and easy-to-access gauge ports
- Contactor with lug connection
- Ground lug connection
- AHRI Certified; ETL Listed
Cabinet Features
- Removable grille style top style grill design compatible with UL 60335-2-40
- Heavy-gauge galvanized-steel cabinet
- Attractive Architectural Gray powder-paint finish with 500-hour salt-spray approval
- Steel louver coil guard
- Single-panel access to controls with space provided for field-installed accessories
- When properly anchored, meets the 2020 Florida Building Code unit integrity requirements for hurricane-type winds (Anchor bracket kits available.)
Goodman GM9S92 Single-Stage, Multi-Speed Gas Furnace Features
Standard
- Heavy-duty aluminized-steel tubular heat exchanger
- Stainless-steel secondary heat exchanger
- Single-stage gas valve
- Durable Silicon Nitride igniter
- Multi-speed ECM blower motor
- Quiet single-speed induced draft blower
- Self-diagnostic control board
- All models comply with California 40 ng/J Low NOx emissions standard• For installation in California’s South Coast Air Quality Management District (SCAQMD) only: This furnace does not meet the SCAQMD Rule 1111 14 ng/J NOx emission limit, and thus is subject to a mitigation fee of up to $450. This furnace is not eligible for the SCAQMD Clean Air Furnace Rebate Program: www.CleanAirFurnaceRebate.com.
- AHRI Certified; ETL Listed
Cabinet
- Designed for multi-position installation — GM9S92: upflow, horizontal left or right
- Certified for direct vent (2-pipe) or non-direct vent (1-pipe)
- Easy-to-install top venting with optional side venting — GM9S92/upflow models only
- Convenient left or right connection for gas and electrical service
- Cabinet air leakage (QLeak) ≤ 2%
- Heavy-gauge steel cabinet with durable finish
- Foil-faced insulated heat exchanger cabinet
- Airtight solid bottom or side return with easy-cut tabs for effortless removal in bottom air-inlet applications
CHPTA Indoor Coil
Standard Features
- All-Aluminum evaporator coil
- Optimized for use with R-410A refrigerant
- Some models suitable for use with R-410A or R-22 refrigerant
- CAPT, CAPTA, CHPT, CHPTA models feature factory-installed thermal expansion valves for cooling and heat pump applications
- CAPF, CAPFA, CAUF, CAUFA, CHPF, CSCF models feature a check flowrator for cooling and heat pump applications
- Vertical and horizontal models available
- 21” depth for easier attic access
- Foil-faced insulation covers the internal casing to reduce cabinet condensation
- Galvanized, leather grain-embossed finish
- Rust resistant, thermoplastic drain pans featuring a low water-retention design
- DecaBDE-free thermoplastic drain pan with secondary drain connections
- UV-resistant drain pan
- AHRI Certified; ETL Listed
Who installs the AC unit after I purchase it?
ACDirect does not yet provide installation services directly. However, most of our customers successfully arrange installation through local licensed HVAC contractors. These systems are designed for professional installation and typically include the components your installer will need.
Here’s how it works:
- Hire a licensed HVAC technician in your area
- Use platforms like Angi, Thumbtack, or a local HVAC directory to find reliable professionals
- Confirm your installer is experienced with the system type you’re purchasing
Note:
Please be aware if you choose to install HVAC equipment yourself and don’t possess proper HVAC licensing, you will void the manufacturer’s factory warranty. If you are capable of a factory-compliant installation yourself, you will need a licensed HVAC contractor to sign off on your work, fully confirming factory-compliant workmanship.
Need help? Contact Our Experts
(866)-862-8922
Hours:
Monday - Friday: 8am to 9pm EST
Saturday: 8am to 8pm EST
Sunday: 11am to 8pm EST
