Use Code MEGA3 for an Extra 3% Off
Free Shipping On Orders Over $1500
America's Leading Discount HVAC Supplier Since 2001
Ask an Expert
866 862 8922
Hours of Operation 8am - 8pm EST
8am - 8pm EST
- 4 ton - best for spaces between 2000-2400 sq ft depending on your home's insulation and your climate
- SEER2 rating helps consumers compare energy efficiency when choosing a new air conditioner. Higher SEER2 ratings mean significant utility savings. The federal minimum is 14 SEER2 with ratings into the 20 SEER2 range. A 20 SEER2 uses half the energy of a 10 seer much like MPG ratings for vehicles.
- If you have an indoor furnace, or air handler, along with an outdoor AC unit, this system will serve as a replacement for both.
- Best for cold climates and if you already have a gas furnace or a gas fuel supply already available.
- You'll need about 25-30 Btu's per sq. foot for warmer winter climates and about 35-50 Btu's per sq. foot for colder winter climates - highly dependent on construction type and insulation values.
Goodman 4 Ton 16.7 SEER2 AC With 120000 BTU 96% AFUE 2-Stage Variable-Speed ECM Gas Furnace System - Horizontal | 2-Stage High Efficiency AC | R32
- Condenser: GLXT7CA4810
- Gas Furnace: GRVT961205DN
- Evaporator Coil: CHPTA6030D3
Furnace BTU Sizing Tonnage Calculator
Heating Square Footage Range by Climate Zone
| Region 1 | Region 2 | Region 3 | Region 4 | Region 5 |
| 30 - 35 BTU's per square foot | 35 - 40 BTU's per square foot | 40 - 45 BTU's per square foot | 45 - 50 BTU's per square foot | 50 - 60 BTU's per square foot |
- 4 ton - best for spaces between 2000-2400 sq ft depending on your home's insulation and your climate
- SEER2 rating helps consumers compare energy efficiency when choosing a new air conditioner. Higher SEER2 ratings mean significant utility savings. The federal minimum is 14 SEER2 with ratings into the 20 SEER2 range. A 20 SEER2 uses half the energy of a 10 seer much like MPG ratings for vehicles.
- If you have an indoor furnace, or air handler, along with an outdoor AC unit, this system will serve as a replacement for both.
- Best for cold climates and if you already have a gas furnace or a gas fuel supply already available.
- You'll need about 25-30 Btu's per sq. foot for warmer winter climates and about 35-50 Btu's per sq. foot for colder winter climates - highly dependent on construction type and insulation values.
Goodman 4 Ton 17.2 SEER2 R32 High-Efficiency Two Stage Cooling Only Condenser
Model Number
GLXT7CA4810
Dimensions
35-1/2" W x 35-1/2" D x 41-5/8"" H
Documents
Limited Warranty
Parts: 10 years
Goodman 96% AFUE 120000 BTU Variable Speed ECM 2 Stage Gas Furnace Upflow / Horizontal | R32
Model Number
GRVT961205DN
Dimensions
24-1/2" W x 29" D x 34-1/2" H
Documents
Limited Warranty
Parts: 10 years | Heat Exchanger: Limited Lifetime
Goodman 5 Ton R32 Evaporator Coil With Internal TXV Horizontal
Model Number
CHPTA6030D3
Dimensions
24-1/2" W x 21" D x 30" H
Documents
Warranty
Parts: 10 years
AHRI Number
216613971
GLXT7C Overview
Standard Features
- Two-Stage Copeland Ultra-Tech scroll compressor
- Quiet two-speed ECM outdoor fan motor
- Integrated communicating ComfortBridge™ Technology
- Commissioning and diagnostics via Bluetooth indoor board via CoolCloud™ App
- Copeland® ComfortAlert™ built in diagnostics
- Copper tube/enhanced aluminum fin coil - 5mm on 2.0-3.0T
- Color-coded terminal strip for non-communicating set-up
- Only two low-voltage wires required in communication mode
- Factory-installed filter drier
- Factory-installed transformer
- Factory-installed high and low-pressure switches
- High-density foam compressor sound blanket
- Fully charged for 15’ of tubing length
- Ambient temperature sensors
- Ground lug connection
- AHRI Certified - ETL Listed
Cabinet Features
- Removable grille-style top design compliant with UL 60335-2-40
- Venturi for increased velocity of airflow
- Heavy-gauge galvanized steel cabinet
- Baked-on powder-paint finish with 500-hour salt-spray approval
- Steel louver coil guard with rust-resistant screws.
- Top and side maintenance access
- Single-panel access to controls with space for field-installed accessories
- Service valves with sweat connections and easy-access gauge ports
- When properly anchored, meets the 2023 Florida Building Code unit integrity requirements for hurricane-type winds (Anchor bracket kits available.)
GRVT96 Overview
Standard Features
- Integrated communicating ComfortBridge™ Technology
- Commissioning and diagnostics via on board Bluetooth with the CoolCloud phone and tablet application
- Heavy-duty aluminized-steel tubular heat exchanger
- Stainless-steel secondary heat exchanger
- Two-stage gas valve provides quiet, economical heating
- Durable Silicon Nitride igniter
- Quiet two-speed induced draft blower
- Compatible with any single-stage thermostat
- Self-diagnostic control board with constant memory fault code history output to a triple 7-segment display
- Color-coded low-voltage terminals with provisions for electronic air cleaner
- Efficient and quiet variable-speed airflow system gently ramps up or down according to heating or cooling demand
- Multiple continuous fan speed options offer quiet air circulation
- Auto-Comfort and enhanced dehumidification modes available
- All models comply with California 40 ng/J Low NOx emissions standard
- Can no longer be installed in California’s South Coast Air Quality Management District (SCAQMD) on or after October 1, 2019.
Cabinet Features
- Designed for multi-position installation — upflow, horizontal left or right
- Certified for direct vent (2-pipe) or non-direct vent (1-pipe)
- Easy to install top venting with optional side venting
- Convenient left or right connection for gas and electrical service
- Cabinet air leakage (QLeak) ≤ 2%
- Heavy-gauge steel cabinet with durable baked-enamel finish
- Fully insulated heat exchanger and blower section
- Airtight solid bottom or side-return with easy-cut tabs for effortless removal in bottom air-inlet applications
CHPTA Overview
Standard Features
- All-Aluminum evaporator coil
- Optimized for use with R-32 refrigerant including circuits and manifolds
- R-32 sensor designed for the life span of the coil
- CAPTA and CHPTA models feature factoryinstalled thermal expansion valves for cooling and heat pump applications
- Standardized copper suction tube stub length
- Vertical and horizontal models available
- 21" depth for easier attic access
- CAPTA and CHPTA models include a single front access panel
- Foil-faced insulation covers the internal casing to reduce cabinet condensation
- Galvanized, leather grain-embossed finish
- Rust resistant, thermoplastic drain pans featuring a low water-retention design
- DecaBDE-free thermoplastic drain pan with secondary drain connections
- Drain pan rails designed to remove and reposition coils with ease without compromising structural integrity
- UV-resistant drain pan
- AHRI certified; ETL listed
Note: Do not use these coils on oil furnaces or any applications where the temperature on the drain pan may exceed 300° F. If these coils are applied with an oil furnace or another application where high temperatures threaten or jeopardize the durability of the drain pan, you must replace the factory-installed drain pan with a high-temperature drain pan. High-temperature drain pan kits are available as field-installed accessories.
Who installs the AC unit after I purchase it?
ACDirect does not yet provide installation services directly. However, most of our customers successfully arrange installation through local licensed HVAC contractors. These systems are designed for professional installation and typically include the components your installer will need.
Here’s how it works:
- Hire a licensed HVAC technician in your area
- Use platforms like Angi, Thumbtack, or a local HVAC directory to find reliable professionals
- Confirm your installer is experienced with the system type you’re purchasing
Note:
Please be aware if you choose to install HVAC equipment yourself and don’t possess proper HVAC licensing, you will void the manufacturer’s factory warranty. If you are capable of a factory-compliant installation yourself, you will need a licensed HVAC contractor to sign off on your work, fully confirming factory-compliant workmanship.
Need help? Contact Our Experts
(866)-862-8922
Hours:
Monday - Friday: 8am to 9pm EST
Saturday: 8am to 8pm EST
Sunday: 11am to 8pm EST