Revolv 4 Ton 13.8 SEER2 95% AFUE Air Conditioner System With High Efficiency Gas Heat For Mobile Home - Downflow

MG2R Overview

The high-efficiency downflow gas furnace is perfect for all types of mobile homes. You can install it in a utility room or a closet. It meets safety standards for use in both the United States and Canada.

For installations in California’s South Coast Air Quality Management District (SCAQMD): This furnace doesn’t meet the NOx emission limit (14 ng/J) set by Rule 1111. Therefore, there’s a mitigation fee of up to $450. Additionally, this furnace isn’t eligible for the Clean Air Furnace Rebate Program. For more details, visit CleanAirFurnaceRebate.com.

• 100% fired and tested: All units and each component (both mechanical and electrical) are tested on the manufacturing line.
• Clean and quiet operation: Due to the unique design of in-shot burners, location of inducer and use of insulation.
• Fixed 30 second blower delay: At burner start-up assures a warm outlet air temperature at furnace start-up. Adjustable blower off settings (60, 90, 120 and 180 seconds).
• Fixed 30-second post purge: Increases life of heat exchanger.
• Dependable, hot surface ignitor: Innovative application of silicon nitride type igniter. Utilizes proven Smartlite^® technology to extend iginiter life.
• Tubular primary heat exchanger: Heavy gauge aluminized steel heat exchanger assures a long life.
• Stainless steel secondary heat exchanger: Assures a long life.
• 60 second fixed cooling cycle blower-off delay (TDR): Increases cooling performance when matched with a Nortek Global HVAC coil.
• Sealed combustion approved for direct vent furnace, category IV venting system: May be vertically or horizontally vented using a two-pipe system for maximum flexibility in installation.
• LP convertible: Simple burner orifice (included w/unit) and gas valve regulator change for ease of convertibility.
• 3 amp fuse protection against low voltage shorts: Protects transformer and control board.
• Low voltage terminal board: For easy field wiring.
• Easy open pawl latch: Secures the door firmly for transit, yet allows easy removal for access.
• Appliance quality door: Protects against rust and other corrosion. Baked enamel finish allows for easy cleaning.
• Fully insulated cabinet: Insures minimized heat loss and quiet operation.
• Color coded wire harness: Designed to fit the components, all with quick-connect fittings for ease of service and replacement.
• Multi-speed ECM blower: Designed to give a wide range of cooling capacities. Switches on PCB, provide ultra easy motor speed selection. 40VA transformer included.
• Diagnostic lights for easy troubleshooting without counting flashes: Dedicated light for flame signal strength and 2 lights in combination to indicate all other fault codes with easy to recognize states without counting flashes.

C84DA Indoor Coil

Standard Features

• Robust Post and Jacket Design has independent louvered panels that are easily removed for service and maintenance, while protecting the coil from yard debris and extreme weather.
• Micro-Channel Coils minimize refrigerant charge and cost; while mounted on a rugged, composite drain pan with damage-preventing molded steps and drainage holes, in a single competitive footprint.
• AccuCharge Systems consist of pre-charged equipment and line sets with unique, quick- connect fittings; to significantly reduce the time, personnel, and skill-set needed to install.
• All DOE Regions can use these same condensers for simplified stocking approach throughout your entire distribution and installation networks.
• Dependable Warranty handled directly by Style Crest’s dedicated HVAC Team, offering the most competitive warranty coverage and service in the Manufactured Housing Industry.
• Evolving Government Standards make it more difficult than ever to find the right AHRI match that will fit manufactured-home furnaces.
• Traditional HUD and Modular Footprints to fit all types of manufactured housing furnaces and coil cavities; C8 coils fit the industry standard 20" W x 24" D HUD furnaces, while C7 coils are available in 4 different footprints for modular furnaces – also commonly used in site-built homes.
• Micro-Channel Systems Reduce Cost by utilizing fully aluminum coils and less system refrigerant charge, as compared to traditional Tube-in-Fin coils with a large amount of expensive copper.
• Revolv Condenser AHRI-Matched Ratings with C8 (Sweat Fit/Quick Connect) or C7 (Sweat Fit) A-coils, for air conditioning and heat pump applications, which can be found in the AHRI Certified Products Directory.
• Pre-installed TXV, UL® Listed, and Leak Tested to 500 psi; with a code-approved 2-opening, dry-type drain pan that does not maintain standing water.
• Dependable Warranty and Support, handled directly by Style Crest’s dedicated HVAC Team, offering the most competitive warranty coverage and service in the Manufactured Housing Industry.